Bingo Plus stock

List of contents of this article:

• 1, What is the valve gap adjustment method
• 2、The six-cylinder engine valve gap adjustment method is What
• 3、How to adjust the valve gap of Auwei 11-liter engine
• 4、Bingo Plus stock How to adjust the valve gap of the car engine?

What is the valve gap adjustment method

The valve gap adjustment method such asNext: Remove the valve cover, remove the valve cover fixing screw, carefully remove the valve cover, and pay attention not to damage the valve cover gasket. Wipe the oil on the valve and rocker arm shaft with a rag to facilitate valve adjustment.

The method of adjusting the valve gap is as follows: Method 1: Cylinder-by-cylinder adjustment method. First, loosen the adjustment screw, tighten the screw shaft with a screwdriver, and determine the adjustment position. Tighten the screw, adjust the gap between the intake valve and the exhaust valve, and gradually adjust the valve gap of other cylinders according to this method. Method 2: Two adjustment methods.

The method of adjusting the valve gap is: cylinder-by-cylinder adjustment method: that is, after determining the stop position of a cylinder piston on the compression according to the cylinder ignition order, the gap between the inlet and exhaust valves of the cylinder can be adjusted.

There are two ways to adjust the engine valve gap. Method 1: Adjustment method for each cylinder.According to the ignition order of the cylinder, after the cylinder piston blocks the compression stop position, the valve gap of the cylinder intake and exhaust can be adjusted. After the adjustment, rotate the crankshaft and use this method to gradually adjust the valve clearance of other cylinders.

There are two ways to adjust the valve gap. The first method is the adjustment method of each cylinder. That is, according to the ignition order of the cylinder, after determining that the piston of a cylinder is in the compression stop position, the valve gap between the intake and exhaust of the cylinder can be adjusted.

What is the six-cylinder engine valve gap adjustment method

For The adjustment method of the 6-cylinder engine in the ignition sequence of 1-5-3-6-2-4 is as follows: the first step: turn the single-cylinder piston to the compression stop point, and adjust as follows: 1 and 5 are arranged, 3 is arranged on the left of 5, 6 is arranged on the right of 1, 2 is arranged on the right of 6, and 4 is arranged on the right side of 3.

The adjustment steps of the six-cylinder engine valve gap are as follows: turn off the engine spark plug and open the valve adjustment shaft. Adjust to the middle position of the specified valve gap (there are different regulations depending on the model and specifications of the engine).Add lubricating oil to the adjustment hinge of the transmission belt, and apply the lubricating oil to the adjustment shaft and pulley shaft.

The inspection and adjustment of the valve gap should be carried out when the valve is completely closed and the valve column falls to the lowest position. Usually, the cylinder compression stroke ends, and the intake and exhaust valves are adjusted at the same time. For a six-cylinder engine, there are two adjustment methods: cylinder-by-cylinder adjustment method, cylinder-by-cylinder adjustment is the adjustment of one cylinder.

How to adjust the valve gap of Auwei 11-liter engine

1. The first method of adjusting the engine valve gap is the cylinder-by-cylinder adjustment method. First, loosen the adjustment screw, then tighten the screw shaft with a screwdriver, determine the adjustment position, tighten the ground again, then adjust the gap between the intake port and the exhaust valve, and then gradually adjust the gap between the other valves in each cylinder.

2. The first method of adjusting the engine valve gap is cylinder-by-cylinder adjustment. First, loosen the adjustment screw, then tighten the screw shaft with a screwdriver, determine the adjustment position, and then tighten it to the ground. Then, adjust the gap between the intake and exhaust valves, and gradually adjust the gap between the valves of other cylinders according to this method.

3. First, find the stop point of one-cylinder compression, and adjust the 4-cylinder intake valve to 0.3MM. THEN TURN THE CRANKSHAFT ONE WEEK TO THE STOP POINT ON THE SIX-CYLINDER AND ADJUST THE 6-CYLINDER INTEALT BALE BALE 0.30MM. Then adjust an exhaust valve 00MM every 120° in the order of 3 from the 6-cylinder exhaust valve.

4. Loosen the screw fixing the rocker arm of the Orway engine. The nut on the top of the valve of the Orway engine can be loosened, and there is no need to screw it down. Use a flat screwdriver to loosen the screw that adjusts the valve gap of the Orway engine.

How to adjust the valve gap of the car engine?

There are two ways to adjust the engine valve gap. Method 1: Adjustment method for each cylinder. According to the ignition order of the cylinder, after the cylinder piston blocks the compression stop position, the valve gap of the cylinder intake and exhaust can be adjusted. After the adjustment, rotate the crankshaft and use this method to gradually adjust the valve clearance of other cylinders.

The adjustment method of the engine valve gap is as follows: preheat the engine to make the cooling water temperature reach 80℃-90℃. Open the timing mark check hole on the clutch housing and cylinder head cover to confirm that the cylinder head bolts are tightened to the specified torque. Rotate the crankshaft to align the "0" engraving line on the flywheel with the marking line on the clutch shell.

The following is the adjustment method of the engine valve clearance: the valve clearance is usually when the engine is in a cold state, and an appropriate gap is left in the valve foot and its transmission mechanism to compensate for the expansion after the valve is heated. This reserved gap is called the valve gap.